Crushing Equipment

Application of Kemai Jaw Crusher is one of the most popular stone crusher in the world, it is ideally suitable for primary and secondary crushing. The highest anti-pressure strength of crushed material is 320MPa. feeding size could be 125mm～1020mm,It is widely used in mining, metallurgy, construction, highway, railroad, and chemistry industries and etc. Many models are available according to your different fineness requirements.

Compared with other crushers, the C series European jaw crusher has the advantages of advanced structure, relative less weight, reliable performance, high capacity and high crushing ratio, , as well as easy to install and convenient to operate. Separated structure simplifies the installation especially in the underground operation. The application of high speed crushing technology allows for the higher crushing ratio and higher capacity. Besides, the shock absorption system effectively protects the foundation from any damage.  

Kemai Impact crushers are used as both primary and secondary crushers in aggregate and in recycle crushing of reinforced concrete, asphalt and other construction materials. The materials crushed by impact crushers shall not be larger than 500mm and its anti pressure strength shall not exceed 350Mpa. The impact crushers are widely used in the industry of water and electricity, expressway, sand and stone, construction, sand production and etc.

Kemai LF impact crusher is an efficient crushing equipment, especially suitable for the treatment of construction waste and other hard materials. This equipment uses high-speed rotating rotor and plate hammer to achieve rapid crushing of materials through high-speed impact and repeated impact. Its design enables it to handle large materials, such as construction waste containing rebar heads, while maintaining high yield and productivity.

CS series cone crusher is based on the introduction and absorption of foreign technology, according to the needs of customers, based on the principle of laminated crushing and the concept of more breakage and less grinding design and development of high swing frequency, optimized cavity and reasonable stroke in one of the modern high-performance crusher.  The spring safety system is an overload protection device, which can make the metal foreign matter pass through the crushing chamber without harming the machine, and adopts the dry oil seal form to isolate the stone powder from the lubricating oil and ensure reliable work. It can be widely used in metal and non-metal mines, cement plants, construction, sand metallurgy and other industries. Non-ferrous ores, granite, limestone, quartzite, sandstone, pebbles, etc.

HPS series multi-cylinder hydraulic cone crusher is mainly composed of fixed cone part, moving cone part, eccentric sleeve part, transmission part, frame part, adjusting ring part, feed bin part, discharge port adjustment part, locking protection cylinder part, fan part, motor part, hydraulic station, lubrication station and special tools part.
Multi-cylinder hydraulic cone crusher is developed on the basis of the spring cone crusher, its basic structure is similar to the spring cone crusher. The difference between multi-cylinder hydraulic and spring cone crusher is that the original 10-16 sets of springs are replaced with 10-16 safety cylinders. It consists of a cylinder body, a piston, a support and a bolt. The cylinder is divided into two chambers A and B by a piston.
The working parts of the multi-cylinder cone crusher are composed of two truncated cones. It is in the active state. The over-iron protection device of the multi-cylinder hydraulic cone crusher is a plurality of hydraulic cylinders, and integrated with the locking protection device, which is installed in the upper and lower machine joints. The structure is more complex, the crushing effect of high hardness ore is good, and it is mostly used for the medium and fine crushing operation of ore and rock.

HS/HT series Single cylinder Hydraulic cone crusher has the characteristics of advanced structural design, excellent crushing capacity, excellent reliability and low production and operation cost. The hydraulic cone breaking realizes many functions such as adjustment of discharge port, cavity cleaning, over-iron and overload protection by lifting and moving cone of a single hydraulic cylinder. Equipped with electronic intelligent discharge port control system, more production process control and job optimization functions are realized. Single cylinder hydraulic cone crusher can be widely used in black, non-ferrous, non-metallic mines and sand and stone and other industrial fields

Kemai PCZ series heavy duty hammer crusher is one of the crushing equipment, the industry hammer crusher series of technology is more advanced a kind of equipment, the use of advanced production technology, to achieve a feeding molding, with high efficiency, energy saving and environmental protection characteristics. The finished material can be adjusted according to the demand, coarse, medium, fine, all kinds of specifications are complete; No sheet, no smooth body, multi-angle and multi-edge positive compressive strength. Especially suitable for highway, construction and large engineering materials. The crusher removes the initial breaking process of the E type machine, and becomes a new model for the completion of the crushing of large and small materials, with large output, high efficiency, small power, saving manpower and material resources, and reducing the crushing cost of materials. The stone broken by the machine is not only complete in specifications, but also uniform and clear, which is the replacement product of the old jaw breaking machine and the plate hammer breaking. This series of products is suitable for crushing all kinds of medium hardness and brittle materials. Such as limestone, coal and other materials. Mainly used in cement, mining, coal preparation, power generation, chemical and building materials industries.